ASTM B221-08 PDF

Leave a comment

Buy Metal Online – Online Metal Store – Order Large or Small Quantity ASTM B T6 Aluminum Equal Leg Structural Angle – Cut to Size Structural. Buy Metal Online – ASTM B T6 Aluminum Round Tube – Order Large or Small Quantity Online – Cut to Size Aluminum Round Tube – No Minimum. Jiangsu Haohua Industry Group as one of the leading suppliers in China to supply ASTM B T6 Aluminum Pipe etc. [Contact person:Ms chris ; Email.

Author: JoJojas Bragami
Country: Lebanon
Language: English (Spanish)
Genre: History
Published (Last): 20 May 2007
Pages: 431
PDF File Size: 12.55 Mb
ePub File Size: 3.38 Mb
ISBN: 500-3-46101-226-9
Downloads: 14832
Price: Free* [*Free Regsitration Required]
Uploader: Kazrall

A minimum of three adjacent replicate specimens shall be taken from each sample and tested.

ASTM B T6 Aluminum Pipe-Aluminium Products-Jiangsu Haohua Industry Group

The test location shall be 9 G Material in the T42 and T62 tempers is not available from the material producers. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters.

C Aatm discontinuity class limits are de? If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. Conformance shall be determined by analyzing samples taken when the ingots are poured, or samples taken from the?

K Yield strength is not applicable in tube. C For the purpose of determining conformance to these limits, an observed value or a calculated value obtained from analysis shall be rounded to the nearest unit in the last right-hand place of the?


For small sizes of tubes, a cut-out portion may be? As much of the rejected material as possible shall be returned to the producer or supplier by the purchaser. Unalloyed aluminum contains a minimum of Chemical milling may be used on? T62G 5 H up through 25 over 25 through 32 up through 32 2. The electrical conductivity shall be determined in accordance with Practice E in the following locations: L Only in tube form. Last previous edition approved in as B — A superscript epsilon e indicates an editorial change since the last revision or reapproval.

D Others includes listed elements for which no speci? Elongation of cut-out round specimens is measured in 43 specimen diameter.


If v221-08 chemical composition has been determined during the course of manufacture, analysis of the? Other methods may be used only when no published ASTM test method is available. Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm.

The cladding composition is more difficult to determine because of the relatively thin layer and because of diffusion of core elements to the cladding. I Minimum yield strength for tube, NOTE 2—For rolled or cold-? NOTE 3—It is standard practice in the United States aluminum industry to determine conformance to the chemical composition limits prior to further processing of ingots into wrought products. Due to the continuous nature of the process, it is not practical to keep a speci?


ASTM B PDF – $ : : National Standards Institute Documents Download Store

The correctness of cladding alloy used can usually be veri? Committee B07 has identi? B — 05a Standard Speci? All tests are performed in accordance with the appropriate ASTM test methods. M Properties not applicable to extruded tube over 2.

I Manganese plus chromium shall total 0. The purchaser shall have the right to perform any of the inspections and tests set forth in this speci? The total for other elements does not include zirconium.

X, and so forth A2. Weight, max per Piece, lb Max Width: E Other Elements—Total shall be the sum of unspeci? For a tube having a diameter larger than can be properly mounted for polishing and examination, the portions of the cross section polished for examination may consist of an arc about 1?

M Composition of cladding alloy applied during the course of manufacture. K Bismuth and lead shall be 0. Rod, Bar and Pro?

Tensile Properties of Material from the Producer 8. The applicable level shall be as speci?

Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend.